Aluminium Slat Fencing

Aluminium Slat Fencing – Horizontal & Vertical Slats

The clean, contemporary look that's taken over residential fencing in Australia. Aluminium slat fencing is low maintenance, built for our climate, and available right here in Sydney. Shop horizontal and vertical slat systems, DIY kits, and bulk trade supply from Chipping Norton.

Why Aluminium Slat Fencing?

Slat fencing has become the go-to choice for modern Australian homes. Where traditional Colorbond gave you privacy in a utilitarian panel, aluminium slats give you the same privacy with a finished, architectural look that adds genuine kerb appeal.

Aluminium doesn't rust. It doesn't rot. It doesn't require repainting. A quality powder-coated aluminium slat fence will look the same in fifteen years as it does on installation day — which is why it's popular with builders, architects, landscapers, and homeowners who want to do it once and forget about it.

31 products

Horizontal Slat Fencing

Horizontal aluminium slat fencing is the dominant style in Australian residential design. Slats run parallel to the ground at a set spacing — typically 50mm to 80mm gaps — creating a clean, linear look that complements contemporary architecture.

  • Boundary fencing
  • Front garden screening
  • Pool surrounds (aesthetic screening — not an AS 1926.1 compliant barrier)
  • Courtyard privacy walls
  • Balcony infill panels

Vertical Slat Fencing

Vertical slat fencing uses the same aluminium slats oriented upright — reading more traditional than horizontal slat but still delivering the clean finish that makes slat fencing so popular. Often used where a more formal look is preferred, or where ground slopes make horizontal slats harder to install.

Horizontal vs Vertical — Which Should You Choose?

  • Style — Horizontal: Contemporary, architectural | Vertical: Modern-traditional
  • Privacy — Horizontal: Fully adjustable by gap spacing | Vertical: Same — adjustable by spacing
  • Best for — Horizontal: Flat blocks, modern homes | Vertical: Sloping blocks, period homes
  • DIY difficulty — Horizontal: Moderate | Vertical: Moderate
  • Street appearance — Horizontal: Clean, linear — makes run feel longer | Vertical: More formal, adds height emphasis

Slat Spacing and Privacy Guide

  • 50mm — Privacy Level: Full privacy | Best For: Boundary fencing, pool surrounds
  • 65mm — Privacy Level: High privacy | Best For: Side fences, garden screening
  • 80mm — Privacy Level: Partial privacy | Best For: Front fencing, breezeway screening
  • 100mm+ — Privacy Level: Open/decorative | Best For: Feature walls, courtyard accents

Slat Fencing on Sloping Blocks

Sloping ground is one of the most common challenges in residential fencing, and aluminium slat fencing handles it better than most. There are two approaches: stepped panels (where each panel is set at the same height but steps down with the slope) and raked panels (where the top and bottom of the panel follow the gradient of the land). The right choice depends on the degree of slope and the look you're going for.

Stepped panels are the more common approach for horizontal slat systems — each panel runs level, with a triangular gap at the base on sloped ground. Raked panels are more common in vertical slat systems, where the slats can be set at an angle to follow the ground line cleanly. If you're dealing with a steep or uneven block, get in touch before ordering — we can help you work out quantities and confirm which approach suits your site.

Our ModuSlat system includes adjustable post bases to accommodate minor variations in ground level, reducing the need for custom fabrication on most residential installs. For severe slopes or retaining wall sections, we recommend a site measure before finalising your order.

Post Accessory Questions

Material costs typically range from $150 to $300 per lineal metre depending on slat width, spacing, panel height, and post system. DIY kits reduce the cost compared to having the fence installed by a contractor.

Aluminium slat fencing can be used for aesthetic screening around pool surrounds, but it does not meet the AS 1926.1 pool safety barrier standard on its own. A compliant pool barrier must be installed as the primary pool enclosure.

The difference is orientation only — horizontal slats run parallel to the ground, vertical slats run upright. Both use the same aluminium slat profiles and post systems. The choice comes down to your home's style and the character of the fence line.

Yes. Our ModuSlat system is designed specifically for DIY installation. Standard tools are all you need. Contact us before ordering if you're working on a sloping block.

No. Aluminium doesn't rust. The powder-coat finish protects the surface from UV and weathering — a key advantage over steel slat systems that require paint maintenance over time.

ModuSlat DIY Slat Fence System

Our ModuSlat system is designed specifically for DIY installation. Pre-cut kits include everything you need to build a complete aluminium slat fence panel-by-panel without specialised tools or trade knowledge.

  • Aluminium slats (pre-cut to panel width)
  • Top and bottom rails
  • Post system
  • All fixing hardware

Available kit sizes: 1.2m, 1.5m, and 1.8m panel heights. A standard 4m kit covers a typical residential side fence run.

Powder Coat Colours

All aluminium slats are powder-coated for durability and UV resistance. Standard colours include Satin Black, Matte White, Monument, Woodland Grey, and Surfmist. Custom colours available for trade orders.