Non-Climbable Fencing in Australia: What It Means and When You Need It
Two fences can look almost identical and behave nothing alike. One gives a child a route over the top in eight seconds. The other does not.
That difference is what non climbable means, and unlike most marketing claims it is measurable.
What does non climbable actually mean?
A non climbable fence offers no horizontal surface, ledge or gap that can be used as a step, and no projecting fixing that can be used as a handhold.
The term gets used two ways in Australia. For pools, AS 1926.1 defines a non climbable zone, an area around the barrier that must stay free of anything climbable, measured as an arc from the top of the barrier. For security, non climbable describes the performance of the fence itself, judged on apertures too small for hands and feet and members arranged so there is nothing to grip.
Both come back to the same three factors: aperture size, horizontal surfaces, and anything nearby that acts as a step.
Where is non climbable fencing required?
Pools are the only place it is written into law as a specific test. Everywhere else it arrives through a specification, a licence condition or an insurer.
- Pools and spas. Mandatory under AS 1926.1, with a 900mm non climbable zone outside the barrier.
- Education sites. State education specifications treat climbability as part of site security. A boundary that can be scaled is a duty of care problem.
- Aged care and health. Usually specified through licensing and accreditation rather than one standard.
- High security and critical infrastructure. AS 5394, the Australian standard for high and extra high security anti-climb fencing.
- Insurers and leases. Often the document that actually decides the fence, long before any standard is quoted.
Education and early learning are the cases worth spelling out. A fenced boundary is not only an access control measure, it is part of supervision. Where a boundary can be climbed in seconds, the fence stops being a barrier and becomes a suggestion, and signage does not fix that. State specifications deal with it through height and material requirements; good site design deals with it by removing the footholds within reach of the line.
How is the non climbable zone measured?
As an arc measured from the top of the barrier, 900mm out and down, kept clear of anything a child could stand on.
Three rules catch people out. The zone is measured to the outside, and the objects inside it are the problem: bins, barbecues, furniture, air conditioners, taps, retaining wall edges, trees, garden beds, letterboxes.
A boundary fence used as part of a pool barrier is treated differently. It generally needs to be 1800mm high, with the non climbable zone maintained on the pool side rather than the street side.
Queensland applies the standard through the QBCC pool safety standard, which accepts a 900mm gap between rails as one way of achieving the zone, allows a 60 degree wedge fitted to rails as a remedy, and limits accessible ledges around the outside of the barrier to 10mm. If you are building in Queensland, work to that document rather than a generic summary.
Which fence types are genuinely non climbable?
Vertical members with nothing horizontal to stand on. The moment a fence offers a rail, a ledge or a lattice, it becomes a ladder.
| Fence type | Why it performs | Verdict |
|---|---|---|
| Vertical picket, flat top, no rails | Nothing to grip, gaps under 100mm | Non climbable |
| Glass panel, face fixed | No ledge, continuous vertical surface | Non climbable |
| 358 anti-climb mesh, 76 x 13mm aperture | Aperture too small for hands and feet | Non climbable |
| Crimp top steel panel | No projecting rail or handhold | Non climbable |
| Chainwire diamond mesh | The lattice is a ladder | Climbable |
| Timber paling with horizontal rails | Rails are steps | Climbable unless wedged or rails set 900mm apart |
Chainwire is the surprise for a lot of buyers. Diamond mesh is a ladder and a topping rail is a handhold. That does not make chainwire wrong, it makes it the wrong choice where climbability is the risk being managed.
What makes a compliant fence climbable after installation?
The site around it. Most failures are objects added after handover, not errors in the fence.
- Wheelie bins or skips parked against the line
- Raised garden beds and mulch pushed up against the base
- Retaining walls and steps built later
- Taps, meter boxes and air conditioners mounted at convenient heights
- Gate hardware used as a step
- Trees and shrubs that grew into the zone
- Trailers, cars and playground equipment stored alongside
How do you check a fence before inspection?
Stand on the outside and look for anything between ankle height and head height that a small child could stand on.
Measure the arc from the top of the barrier rather than eyeballing it. Check that no gap passes a 100mm sphere. Confirm the gate is self closing from every open position, self latching, and that the release sits where the standard requires. Then photograph each section with a tape measure in frame, because that is the evidence that settles a dispute later.
Which products are non climbable?
Flat top and crimp top panel systems, vertical picket profiles and 358 mesh, all available in the security range.
Our anti-climb fence panels guide covers the aperture and profile differences in detail. For the standards behind the requirement, read security fencing compliance in Australia. For pool specific barrier rules, see pool fence regulations.
Browse the commercial security fencing range to match a profile to the site.
Why buy from Fencing Components
- Steel and aluminium fencing manufactured to Australian Standards
- Over 22 powder-coat colour options across the range
- Nationwide delivery — order online or visit Chipping Norton NSW
- Open to the public — no minimum order
- Click & Collect available
58 Governor Macquarie Drive, Chipping Norton NSW 2170 | 02 9755 2666
Need a fence that cannot be climbed, not one that says it cannot?
Send the site type and we will tell you which profile meets the requirement and which one just looks the part.
Non climbable questions, answered
What is a non climbable zone?
An area measured as a 900mm arc from the top of a pool barrier that must be kept clear of anything a child could use as a foothold.
Is chainwire non climbable?
No. Diamond mesh and a topping rail give both footholds and handholds. Chainwire is appropriate where climbability is not the risk being managed.
Does non climbable fencing have to be a set height?
For pools the barrier must be at least 1200mm, and a boundary fence used as part of the barrier is generally 1800mm. Security heights are set by the site specification.
Is anti-climb the same as non climbable?
They describe the same performance. Non climbable is the term used in pool barrier regulation; anti-climb is the term used in security fencing specifications.