Chainwire Fencing for Rural and Agricultural Boundaries: What Works and Why

✓ Australian Standard Certified Panels✓ Nationwide Delivery✓ Open to the Public✓ 15+ Years Experience✓ 22 Powder Coat Colours✓ Click & Collect Available✓ Australian Standard Certified Panels✓ Nationwide Delivery✓ Open to the Public✓ 15+ Years Experience✓ 22 Powder Coat Colours✓ Click & Collect Available
Chain Wire Fencing🕔 5 min read📅 4 November 2026
Galvanised fencing posts and strainer assemblies for a chainwire boundary
On a long rural run, the posts and the coating decide how long it lasts.
The short version Chainwire is still the cheapest way to enclose a long rural boundary, and the specification is where the money is won or lost. Fabric to AS 1725.1 in 2.50mm light duty or 3.15mm heavy duty, post centres no more than 3330mm, a coating class that matches the corrosivity of the site, and strainer assemblies at every end and corner. Get those four right and the fence is still straight in fifteen years.

A rural boundary is a different job to a suburban fence. The runs are longer, the wind is worse, the ground moves, and nobody walks the line every week to see how it is going.

Chainwire survives that better than most materials. What fails out there is the specification, not the product.

Why chainwire suits long rural boundaries

It is the lowest cost per metre of any boundary material, it lets wind through instead of catching it, and it repairs in sections.

A solid panel fence on an exposed rural boundary is a sail. Every panel takes the full wind load and passes it into the posts, which is why solid fencing on open country needs heavier sections and deeper footings than the same fence in a suburb. Chainwire lets most of that wind through.

The other advantage is repair. When a branch or a vehicle takes out ten metres, you replace ten metres of fabric and a post. Nobody is reordering panels for a paddock.

Which duty grade do you actually need?

Light duty is 2.50mm wire, heavy duty is 3.15mm, and 4.00mm covers the hard cases. For anything carrying stock, machinery or a security expectation, heavy duty is the starting point.

Duty Wire diameter Where it fits
Light duty 2.50mm Low risk boundaries, internal divisions, short runs
Heavy duty 3.15mm Stock boundaries, depots, machinery yards, exposed runs
Extra 4.00mm Gates, corners, high impact points, heavy stock pressure

The numbers matter more than they look. Light duty 2.50mm fabric carries roughly 60 percent of the load bearing capacity of 3.15mm heavy duty fabric. Over a long rural run, that is the difference between a fence that lasts and one that gets restring at ten years.

Galvanised, PVC coated or fuse bonded?

Heavy galvanised for inland and general rural use, PVC coated where you want colour and abrasion resistance, fuse bonded where corrosion is severe.

Galvanised fabric is specified by coating class. Standard grade suits mild inland conditions. Heavy galvanised, Class A, is the call for coastal influence, industrial atmosphere, and anywhere the fence has to outlast a mortgage.

PVC coated fabric adds a polymer layer over galvanised wire. It gives colour, resistance to abrasion from stock, and a second barrier against corrosion, as long as the coating stays intact.

Fuse bonded fabric bonds the PVC directly to the wire rather than extruding a loose sleeve over it. There is no gap between coating and wire for moisture to travel along, which is why it holds up better near the coast and in high humidity.

What mesh, height and post spacing for a rural run?

Nominal pitch up to 50mm, post centres no more than 3330mm, and a strainer assembly at every end, corner and gate.

Chain link fabric to AS 1725.1 is limited to a 50mm nominal pitch, measured across the diamond. That is why standard chainwire is 50mm and anything tighter is a security or sports specification.

Common heights are 1800mm, 2100mm and 2400mm. On rural boundaries 1800mm handles stock and general exclusion, and taller runs are usually about people rather than animals.

Post spacing is where rural jobs get built cheap and fail early. Long spans look fine on day one and sag by year three once tension comes off. Strainer assemblies at ends, corners and gates, line posts at the spacing the standard allows, and proper tensioning are what keep a run straight. Lacing wire and tie wire are specified too, with 2.00mm core lacing wire for tying fabric to posts and 1.57mm tie wire for securing fabric to line wires.

What about coastal, inland and UV?

Corrosivity decides the coating, not the budget. Inland sites can run standard galvanising. Coastal sites cannot.

Salt deposition, humidity and prevailing wind decide how fast a coating fails. Australian corrosivity categories give you a way to choose a coating instead of guessing. Any site within wind driven spray of the coast needs heavier galvanising, or fuse bonded PVC over galvanised wire, or both.

UV matters for coated fabric. PVC chalks and fades over time, faster in brighter colours. That is cosmetic rather than structural, but it is worth setting the expectation before the fence goes in, not after the first summer.

What about gates and access points?

Match the gate to the fabric and put a strainer on both sides. Gates are where a rural fence moves first.

Wide farm and depot openings are better served by a braced gate frame on a wheel or a cantilever system than by a long single leaf hanging off one post. Drop bolts, heavy hinges and a latch that works with gloves on matter more than the finish does.

Every gate is a load point. Two strainer assemblies, one either side of the opening, stop the fence pulling away from the gate.

Depots and sports courts sit between the rural and security cases. A depot usually wants height and a tighter mesh, to stop climbing and to keep equipment in. A court enclosure wants height, a tighter pitch so balls stay inside, and a frame that does not rattle itself loose. Same fabric family, three different specifications, so say which one you are quoting.

How do you order chainwire in bulk?

Give the supplier a line schedule, not a guess at lineal metres.

That schedule needs total lineal metres by height, the number of ends, corners and gates, wire diameter and duty, coating class, the selvedge at top and bottom, post type and length, and the delivery point. Note terrain and access, because a paddock that needs a four wheel drive is a different freight quote.

Rolls are supplied in strained lengths, so the figure you need is the strained length of the run, not the distance walked on a GPS. Add for slope and for the tension you intend to hold.

For the fabric and fitting detail behind these numbers, read chain link fence specifications in Australia. For heavier institutional specifications, see chainwire for schools and industrial sites, and browse fencing posts for line and strainer options.

Why buy from Fencing Components

  • Steel and aluminium fencing manufactured to Australian Standards
  • Over 22 powder-coat colour options across the range
  • Nationwide delivery — order online or visit Chipping Norton NSW
  • Open to the public — no minimum order
  • Click & Collect available

58 Governor Macquarie Drive, Chipping Norton NSW 2170  |  02 9755 2666

Pricing a kilometre of boundary?

Send the line schedule and we will quote fabric, posts and fittings to the same specification.

Rural chainwire questions, answered

What is standard chainwire mesh size?

50mm nominal pitch, measured across the diamond, is the maximum for fabric to AS 1725.1.

What is the difference between fuse bonded and PVC coated chainwire?

Fuse bonded PVC is bonded directly to the wire. PVC coated fabric has an extruded sleeve over galvanised wire, which can allow moisture between coating and wire.

How far apart should chainwire posts be?

AS 1725.1 allows post centres up to 3330mm. Long spans sag faster, so treat the spacing as a specification decision rather than a default.

Can chainwire be used for stock?

Yes, provided wire diameter, height and post spacing suit the stock pressure. Light duty 2.50mm fabric is not appropriate for heavy stock.

Back to blog